流體傳動 hydraulic power
液壓技術 hydraulics
液力技術 hydrodynamics
氣液技術 hydropneumatics
運行工況 operating conditions
額定工況 rated conditions
極限工況 limited conditions
瞬態工況 instantaneous conditions
穩態工況 steady-state conditions
許用工況 acceptable conditions
連續工況 continuous working conditions
實際工況 actual conditions
效率 efficiency
旋轉方向 direction of rotation
公稱壓力 nominal pressure
工作壓力 working pressure
進口壓力 inlet pressure
出口壓力 outlet pressure
壓降 pressure drop；differential pressure
背壓 back pressure
啟動壓力 breakout pressure
充油壓力 charge pressure
開啟壓力 cracking pressure
峰值壓力 peak pressure
運行壓力 operating pressure
耐壓試驗壓力 proof pressure
沖擊壓力 surge pressure
靜壓力 static pressure
系統壓力 system pressure
控制壓力 pilot pressure
充氣壓力 pre-charge pressure
吸入壓力 suction pressure
調壓偏差 override pressure
額定壓力 rated pressure
耗氣量 air consumption
泄漏 leakage
內泄漏 internal leakage
外泄漏 external leakage
層流 laminar flow
紊流 turbulent flow
氣穴 cavitation
流量 flow rate

排量 displacement
額定流量 rated flow
供給流量 supply flow
流量系數 flower factor
滯環 hysteresis
圖形符號 graphical symbol
液壓氣動元件圖形符號 symbols for hydraulic and pneumatic components
流體邏輯元件圖形符號 symbols for fluid logic devices
邏輯功能圖形符號 symbols for logic functions
回路圖 circuit diagram
壓力－時間圖 pressure time diagram
功能圖 function diagram
循環 circle
自動循環 automatic cycle
工作循環 working cycle
循環速度 cycling speed
工步 phase
停止工步 dwell phase
工作工步 working phase
快進工步 rapid advance phase
快退工步 rapid return phase
頻率響應 frequency response
重復性 repeat ability
復現性 reproducibility
漂移 drift
波動 ripple
線性度 linearity
線性區 linear region
液壓鎖緊 hydraulic lock
液壓卡緊 sticking
變量泵 variable displacement pump
泵的控制 control of pump
齒輪泵 gear pump
葉片泵 vane pump
柱塞泵 piston pump
軸向柱塞泵 axial piston pump
法蘭安裝 flange mounting
底座安裝 foot mounting
液壓馬達 hydraulic motor
剛度 stiffness
中位 neutral position
零位 zero position
自由位 free position
缸 cylinder
有桿端 rod end
無桿端 rear end
外伸行程 extend stroke
內縮行程 retract stroke
緩沖 cushioning
工作行程 working stroke
負載壓力 induced pressure
輸出力 force
實際輸出力 actual force
單作用缸 single-acting cylinder
雙作用缸 double-acting cylinder
差動缸 differential cylinder
伸縮缸 telescopic cylinder
閥 valve
底板 sub-plate
油路塊 manifold block
板式閥 sub-plate valve
疊加閥 sandwich valve
插裝閥 cartridge valve
滑閥 slide valve
錐閥 poppet valve
閥芯 valve element
閥芯位置 valve element position
單向閥 check valve
液控單向閥 pilot-controlled check valve
梭閥 shuttle valve
壓力控制閥 pressure relief valve
溢流閥 pressure relief valve
順序閥 sequence valve
減壓閥 pressure reducing |<< << < >>